“Dom0less” is a set of Xen features that enable the deployment of a Xen system without an control domain (often referred to as “dom0”). Each feature can be used independently from the others, unless otherwise stated.
This feature enables Xen to create a set of DomUs at boot time. Information about the DomUs to be created by Xen is passed to the hypervisor via Device Tree. Specifically, the existing Device Tree based Multiboot specification has been extended to allow for multiple domains to be passed to Xen. See docs/misc/arm/device-tree/booting.txt for more information about the Multiboot specification and how to use it.
Currently, a control domain (“dom0”) is still required, but in the future it will become unnecessary when all domains are created directly from Xen. Instead of waiting for the control domain to be fully booted and the Xen tools to become available, domains created by Xen this way are started right away in parallel. Hence, their boot time is typically much shorter.
U-Boot needs to load not just Xen, the device tree binary, the dom0 kernel and ramdisk. It also needs to load the kernel and ramdisk of any additional domains to boot. For example if this is the bootcmd for Xen and Dom0:
tftpb 0x1280000 xen.dtb
tftpb 0x0x80000 xen-Image
tftpb 0x1400000 xen.ub
tftpb 0x9000000 xen-rootfs.cpio.gz.u-boot
bootm 0x1400000 0x9000000 0x1280000If we want to add one DomU with Image-DomU as the DomU kernel and ramdisk-DomU as DomU ramdisk:
tftpb 0x1280000 xen.dtb
tftpb 0x80000 xen-Image
tftpb 0x1400000 xen.ub
tftpb 0x9000000 xen-rootfs.cpio.gz.u-boot
tftpb 0x2000000 Image-DomU
tftpb 0x3000000 ramdisk-DomU
bootm 0x1400000 0x9000000 0x1280000In addition to loading the necessary binaries, we also need to advertise the presence of the additional VM and its configuration. It is done via device tree adding a node under /chosen as follows:
domU1 {
#address-cells = <1>;
#size-cells = <1>;
compatible = "xen,domain";
memory = <0 0x20000>;
cpus = <1>;
vpl011;
module@2000000 {
compatible = "multiboot,kernel", "multiboot,module";
reg = <0x2000000 0xffffff>;
bootargs = "console=ttyAMA0";
};
module@30000000 {
compatible = "multiboot,ramdisk", "multiboot,module";
reg = <0x3000000 0xffffff>;
};
};Where memory is the memory of the VM in KBs, cpus is the number of cpus. module@2000000 and module@3000000 advertise where the kernel and ramdisk are in memory.
Note: the size specified should exactly match the size of the Kernel/initramfs. Otherwise, they may be unusable in Xen (for instance if they are compressed).
See docs/misc/arm/device-tree/booting.txt for more information.
Domains started by Xen at boot time currently have the following limitations:
They cannot be properly shutdown or rebooted using xl. If one of them crashes, the whole platform should be rebooted.
Some xl operations might not work as expected. xl is meant to be used with domains that have been created by it. Using xl with domains started by Xen at boot might not work as expected.
The GIC version is the native version. In absence of other information, the GIC version exposed to the domains started by Xen at boot is the same as the native GIC version.
No PV drivers. There is no support for PV devices at the moment. All devices need to be statically assigned to guests.
Pinning vCPUs of domains started by Xen at boot can be done from the control domain, using xl vcpu-pin as usual. It is not currently possible to configure vCPU pinning without a control domain. However, the NULL scheduler can be selected by passing sched=null to the Xen command line. The NULL scheduler automatically assigns and pins vCPUs to pCPUs, but the vCPU-pCPU assignments cannot be configured.
‘xl console’ command will not attach to the domain’s console in case of dom0less. DomU are domains created by Xen (similar to Dom0) and therefore they are all managed by Xen and some of the commands may not work.
A user is allowed to configure the key sequence to switch input. Pressing the Xen “conswitch” (Ctrl-A by default) three times switches input in case of dom0less mode.
Domains created by Xen will have no name at boot. Domain-0 has a name thanks to the helper xen-init-dom0 called at boot by the initscript. If you want to setup DomU name, then you will have to create the xenstore node associated. By default DomU names are shown as ‘(null)’ in the xl domains list.